Suzuki SX4 / S-cross (2014-2019) Fuse Diagram • FuseCheck.com

Checking and Replacing Fuses

The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. If any lights, accessories or other electrical controls do not operate, inspect the corresponding fuse. Look through the clear side of the fuse to see if the metal wire inside is separated. If it is, the fuse is blown and should be replaced.

Notice

Before replacing the fuses, turn the ignition switch to the “LOCK” position and turn off all electrical accessories.
Always be sure to replace a blown fuse with a fuse of the correct amperage. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Never use a substitute such as a wire even for a temporary repair, or extensive electrical damage, and a fire can result.
We recommend always carrying replacement fuses in the vehicle.
If the main fuse or a primary fuse blows, be sure to have your vehicle inspected by an authorised Suzuki workshop.
If you replace a fuse and the new one blows in a short period of time, you may have a major electrical problem. Have your vehicle inspected immediately by your authorised Suzuki workshop.

Your vehicle has three types of fuses, as described below:

Main fuse: The main fuse takes current directly from the battery.
Primary fuses: These fuses are between the main fuse and individual fuses, and are for electrical load groups.
Individual fuses: These fuses are for individual electrical circuits.

Instrument Panel Fuse Box

The fuse box is located under the left side of the dashboard.

LHD: To approach the fuses, unscrew the screws and remove the cover (1).

RHD: To approach the fuses, remove the clips (1) by prying it off with a flat blade screwdriver as shown in the illustration, then remove the cover (2).

№	A	Function/component
1	-	Not used
2	20	Power window timer
3	15	Steering lock
4	20	Rear defogger
5	20	SunrooP
6	10	DRL
7	10	Heated mirror
8	7.5	Starting signal
9	15	Accessory socket 2
10	30	Power window
11	10	Hazard
12	7.5	BCM
13	15	Ignition coil
14	10	ABS control module
15	15	Accessory socket
16	10	A-STOP controller
17	15	Horn
18	10	Stop light
19	10	Air bag
20	10	Back-up light
21	15	Wiper / Washer
22	30	Front wiper
23	10	Dome light
24	15	4WD
25	7.5	RR fog lamp
26	-	Not used
27	7.5	Ignition-1 signal
28	15	Radio 2
29	10	Accessory socket 3
30	15	Radio
31	10	Tail lamp
32	20	D/L
33	7.5	Cruise control
34	10	Meter
35	7.5	Ignition-2 signal
36	20	Seat heater

Engine Compartment Fuse Box Diagram

The main fuse, primary fuses, and some of the individual fuses are located in the engine compartment. If the main fuse blows, no electrical component will function. If a primary fuse blows, no electrical component in the corresponding load group will function.

To remove a fuse, use the fuse puller provided in the fuse box. The amperage of each fuse is shown in the back of the fuse box cover.

№	A	Function/component
1	60	FL7
2	80	FL6
3	100	FL5
4	80	FL4
5	100	FL3
6	100	FL2
7	120	FL1
8	7.5	Ignition-1 signal 2 (D16AA)
9	30	Radiator fan 2
10	20	Front fog light
11	7.5	Headlight 2
12	25	ABS control module
13	25	Headlight
14	30	Back up
15	40	Ignition switch
16	40	ABS motor
17	30	Starting motor
18	30	Radiator fan
19	30	FI main
20	20	Fuel pump
21	10	Air compressor
22	7.5	ECM (D13A)
23	30	Blower fan
24	10	FI 2 (D13A)
25	20	INJ DRV (D13A)
26	7.5	Starting signal
27	15	Headlight (Left)
28	15	Headlight high (Left)
29	7.5	FI 2 (D16AA)
30	20	INJ DRV (D16AA)
31	15	FI 3 (D16AA)
32	15	Headlight (Right)
33	15	Headlight high (Right)
34	50	Ignitbn switch 2
35	50	Battery